galice.C

Go to the documentation of this file.

// In order to create galice.root follow the steps shown below
//
//  gAlice->Init("galice.C");
//  AliRunLoader::Instance()->Write();
//  delete AliRunLoader::Instance();
//



void Config()
{
    AliRunLoader* runLoader = AliRunLoader::Open("galice.root", AliConfig::GetDefaultEventFolderName(), "recreate");
    runLoader->SetCompressionLevel(2);
    runLoader->SetNumberOfEventsPerFile(1);
    gAlice->SetRunLoader(runLoader);

    gSystem->Load("libgeant321");
    new TGeant3("C++ Interface to Geant3");

    // Field (L3 0.4 T)
    TGeoGlobalMagField::Instance()->SetField(new AliMagF("Maps","Maps", 1., 1., AliMagF::k5kG));

    Int_t   iABSO  =  0;
    Int_t   iDIPO  =  0;
    Int_t   iFMD   =  0;
    Int_t   iFRAME =  0;
    Int_t   iHALL  =  0;
    Int_t   iITS   =  1;
    Int_t   iMAG   =  0;
    Int_t   iMUON  =  0;
    Int_t   iPHOS  =  0;
    Int_t   iPIPE  =  0;
    Int_t   iPMD   =  0;
    Int_t   iHMPID  =  0;
    Int_t   iSHIL  =  0;
    Int_t   iT0 =  0;
    Int_t   iTOF   =  0;
    Int_t   iTPC   =  1;
    Int_t   iTRD   =  0;
    Int_t   iZDC   =  0;
    Int_t   iEMCAL =  0;
    Int_t   iACORDE   =  0;
    Int_t   iVZERO =  0;
    runLoader->CdGAFile();
    //=================== Alice BODY parameters =============================
    AliBODY *BODY = new AliBODY("BODY", "Alice envelop");

    if (iMAG)
    {
        //=================== MAG parameters ============================
        // --- Start with Magnet since detector layouts may be depending ---
        // --- on the selected Magnet dimensions ---
        AliMAG *MAG = new AliMAG("MAG", "Magnet");
    }


    if (iABSO)
    {
        //=================== ABSO parameters ============================
        AliABSO *ABSO = new AliABSOv0("ABSO", "Muon Absorber");
    }

    if (iDIPO)
    {
        //=================== DIPO parameters ============================

        AliDIPO *DIPO = new AliDIPOv2("DIPO", "Dipole version 2");
    }

    if (iHALL)
    {
        //=================== HALL parameters ============================

        AliHALL *HALL = new AliHALL("HALL", "Alice Hall");
    }


    if (iFRAME)
    {
        //=================== FRAME parameters ============================

        AliFRAMEv2 *FRAME = new AliFRAMEv2("FRAME", "Space Frame");
  if (geo == kHoles) {
      FRAME->SetHoles(1);
  } else {
      FRAME->SetHoles(0);
  }
    }

    if (iSHIL)
    {
        //=================== SHIL parameters ============================

        AliSHIL *SHIL = new AliSHILv2("SHIL", "Shielding Version 2");
    }


    if (iPIPE)
    {
        //=================== PIPE parameters ============================

        AliPIPE *PIPE = new AliPIPEv0("PIPE", "Beam Pipe");
    }
 
    if(iITS) {

    //=================== ITS parameters ============================
    //
    // As the innermost detector in ALICE, the Inner Tracking System "impacts" on
    // almost all other detectors. This involves the fact that the ITS geometry
    // still has several options to be followed in parallel in order to determine
    // the best set-up which minimizes the induced background. All the geometries
    // available to date are described in the following. Read carefully the comments
    // and use the default version (the only one uncommented) unless you are making
    // comparisons and you know what you are doing. In this case just uncomment the
    // ITS geometry you want to use and run Aliroot.
    //
    // Detailed geometries:         
    //
    //
    //AliITS *ITS  = new AliITSv5symm("ITS","Updated ITS TDR detailed version with symmetric services");
    //
    //AliITS *ITS  = new AliITSv5asymm("ITS","Updates ITS TDR detailed version with asymmetric services");
    //
  AliITSvPPRasymmFMD *ITS  = new AliITSvPPRasymmFMD("ITS","New ITS PPR detailed version with asymmetric services");
  ITS->SetMinorVersion(2);           // don't touch this parameter if you're not an ITS developer
  ITS->SetReadDet(kFALSE);           // don't touch this parameter if you're not an ITS developer
    //    ITS->SetWriteDet("$ALICE_ROOT/ITS/ITSgeometry_vPPRasymm2.det");  // don't touch this parameter if you're not an ITS developer
  ITS->SetThicknessDet1(200.);   // detector thickness on layer 1 must be in the range [100,300]
  ITS->SetThicknessDet2(200.);   // detector thickness on layer 2 must be in the range [100,300]
  ITS->SetThicknessChip1(200.);  // chip thickness on layer 1 must be in the range [150,300]
  ITS->SetThicknessChip2(200.);  // chip thickness on layer 2 must be in the range [150,300]
  ITS->SetRails(0);      // 1 --> rails in ; 0 --> rails out
  ITS->SetCoolingFluid(1);   // 1 --> water ; 0 --> freon
  //
    //AliITSvPPRsymm *ITS  = new AliITSvPPRsymm("ITS","New ITS PPR detailed version with symmetric services");
    //ITS->SetMinorVersion(2);                                       // don't touch this parameter if you're not an ITS developer
    //ITS->SetReadDet(kFALSE);                                       // don't touch this parameter if you're not an ITS developer
    //ITS->SetWriteDet("$ALICE_ROOT/ITS/ITSgeometry_vPPRsymm2.det"); // don't touch this parameter if you're not an ITS developer
    //ITS->SetThicknessDet1(200.);   // detector thickness on layer 1 must be in the range [100,300]
    //ITS->SetThicknessDet2(200.);   // detector thickness on layer 2 must be in the range [100,300]
    //ITS->SetThicknessChip1(200.);  // chip thickness on layer 1 must be in the range [150,300]
    //ITS->SetThicknessChip2(200.);  // chip thickness on layer 2 must be in the range [150,300]
    //ITS->SetRails(0);              // 1 --> rails in ; 0 --> rails out
    //ITS->SetCoolingFluid(1);       // 1 --> water ; 0 --> freon
    //
    //
    // Coarse geometries (warning: no hits are produced with these coarse geometries and they unuseful 
    // for reconstruction !):
    //                                                     
    //
    //AliITSvPPRcoarseasymm *ITS  = new AliITSvPPRcoarseasymm("ITS","New ITS PPR coarse version with asymmetric services");
    //ITS->SetRails(0);                // 1 --> rails in ; 0 --> rails out
    //ITS->SetSupportMaterial(0);      // 0 --> Copper ; 1 --> Aluminum ; 2 --> Carbon
    //
    //AliITS *ITS  = new AliITSvPPRcoarsesymm("ITS","New ITS PPR coarse version with symmetric services");
    //ITS->SetRails(0);                // 1 --> rails in ; 0 --> rails out
    //ITS->SetSupportMaterial(0);      // 0 --> Copper ; 1 --> Aluminum ; 2 --> Carbon
    //                      
    //
    //
    // Geant3 <-> EUCLID conversion
    // ============================
    //
    // SetEUCLID is a flag to output (=1) or not to output (=0) both geometry and
    // media to two ASCII files (called by default ITSgeometry.euc and
    // ITSgeometry.tme) in a format understandable to the CAD system EUCLID.
    // The default (=0) means that you dont want to use this facility.
    //
     ITS->SetEUCLID(0);  
    }

    if (iTPC)
    {
        //============================ TPC parameters ================================
        // --- This allows the user to specify sectors for the SLOW (TPC geometry 2)
        // --- Simulator. SecAL (SecAU) <0 means that ALL lower (upper)
        // --- sectors are specified, any value other than that requires at least one 
        // --- sector (lower or upper)to be specified!
        // --- Reminder: sectors 1-24 are lower sectors (1-12 -> z>0, 13-24 -> z<0)
        // ---           sectors 25-72 are the upper ones (25-48 -> z>0, 49-72 -> z<0)
        // --- SecLows - number of lower sectors specified (up to 6)
        // --- SecUps - number of upper sectors specified (up to 12)
        // --- Sens - sensitive strips for the Slow Simulator !!!
        // --- This does NOT work if all S or L-sectors are specified, i.e.
        // --- if SecAL or SecAU < 0
        //
        //
        //-----------------------------------------------------------------------------

        //  gROOT->LoadMacro("SetTPCParam.C");
        //  AliTPCParam *param = SetTPCParam();
        AliTPC *TPC = new AliTPCv2("TPC", "Default");

        // All sectors included 
        TPC->SetSecAU(-1);
        TPC->SetSecAL(-1);
    }


    if (iTOF) {
  if (geo == kHoles) {
        //=================== TOF parameters ============================
      AliTOF *TOF = new AliTOFv2FHoles("TOF", "TOF with Holes");
  } else {
      AliTOF *TOF = new AliTOFv4T0("TOF", "normal TOF");
  }
    }


    if (iHMPID)
    {
        //=================== HMPID parameters ===========================
        AliHMPID *HMPID = new AliHMPIDv3("HMPID", "normal HMPID");

    }


    if (iZDC)
    {
        //=================== ZDC parameters ============================

        AliZDC *ZDC = new AliZDCv2("ZDC", "normal ZDC");
    }

    if (iTRD)
    {
        //=================== TRD parameters ============================

        AliTRD *TRD = new AliTRDv1("TRD", "TRD slow simulator");

        // Select the gas mixture (0: 97% Xe + 3% isobutane, 1: 90% Xe + 10% CO2)
        TRD->SetGasMix(1);
  if (geo == kHoles) {
      // With hole in front of PHOS
      TRD->SetPHOShole();
      // With hole in front of HMPID
      TRD->SetHMPIDhole();
  }
      // Switch on TR
      AliTRDsim *TRDsim = TRD->CreateTR();
    }

    if (iFMD)
    {
        //=================== FMD parameters ============================
  AliFMD *FMD = new AliFMDv1("FMD", "normal FMD");
        FMD->SetRingsSi1(256);
        FMD->SetRingsSi2(128);
        FMD->SetSectorsSi1(20);
        FMD->SetSectorsSi2(40);      
   }

    if (iMUON)
    {
        //=================== MUON parameters ===========================

        AliMUON *MUON = new AliMUONv1("MUON", "default");
    }
    //=================== PHOS parameters ===========================

    if (iPHOS)
    {
        AliPHOS *PHOS = new AliPHOSv1("PHOS", "IHEP");
    }


    if (iPMD)
    {
        //=================== PMD parameters ============================
        AliPMD *PMD = new AliPMDv1("PMD", "normal PMD");
    }

    if (iT0)
    {
        //=================== T0 parameters ============================
        AliT0 *T0 = new AliT0v1("T0", "T0 Detector");
    }

    if (iEMCAL)
    {
        //=================== EMCAL parameters ============================
        AliEMCAL *EMCAL = new AliEMCALv1("EMCAL", "EMCALArch1a");
    }

     if (iACORDE)
    {
        //=================== ACORDE parameters ============================
        AliACORDE *ACORDE = new AliACORDEv1("ACORDE", "normal ACORDE");
    }

     if (iVZERO)
    {
        //=================== ACORDE parameters ============================
        AliVZERO *VZERO = new AliVZEROv2("VZERO", "normal VZERO");
    }

}